INFICON Noticias

Más información sobre nuestros productos y servicios.

OLED Crystal Introduction
Seminarios web

OLED Crystal Introduction

Ubicación
Online
Idioma
English
Duración
31 min

Description

INFICON is proud to introduce the OLED crystal! The OLED crystal is like no other crystal on the market. This new design generates a rapid response when it comes to a magnesium deposition, which significantly reduces pre-depositing waste. 

This webinar will give an overview on the different applications used for processing thin films. 

We will be covering the following topics: 

  • OLED Overview 
  • Magnesium Delay Issue 
  • Our OLED Crystal Solution

Related webinars

Webinar
How to increase efficiency in vacuum leak testing with I·Zero
50 min
English
Más información
Webinar
Have your process under control with Augent OPG550

Intelligent solution for real-time vacuum gas monitoring

40 min
English
Más información
Webinar
Factory Optimization - Part I

How to measure your factory performance

50 min
English
Más información
Webinar
Factory Optimization - Part II

How to measure your factory performance

50 min
English
Más información
Webinar
Factory Optimization - Part III

How to measure your factory performance

50 min
English
Más información
Webinar
Is Your Pressure under Control?
Pressure Control and Monitoring in SEMI ALD Processes
1 h
English
Más información
Webinar
Optical revolution in vacuum pressure & gas composition measurement
35 min
English
Más información
Webinar
UL6000 Fab - The ultimate in vacuum leak testing
17 min
English
Más información
Webinar
Thin Film and QCM Basics
30 minutes
English
Más información
Webinar
INFICON Multi-layer Compensation System
15 minutes
English
Más información
Webinar
QCM Troubleshooting
30 min
English
Más información
Webinar
Thin Film Applications
40 min
English
Más información
Webinar
Mastering Vacuum Measurements

A Basic Guide to Capacitive Vacuum Gauges

36 minutes
English
Más información
Webinar
QCMs and Thin Film Processes in Semi

QCM use in the semiconductor industry for processes like ALD, E-beam, resistive source and sputtering.

22 minutes
English
Más información
Webinar
Temperature Compensation for QCMs

Quartz crystal microbalance (QCM) technology has been used for decades to control deposition rate and thickness for the most complex processes seen in the ophthalmic, optical, display, and solar markets. INFICON has recently made a new advancement in QCM technology to address a problem seen across all of these industries related to QCM temperature effects. Thermal shock can cause QCM thickness errors which can decrease yield and increase manufacturing costs if temperature is not accounted for correctly.

Temperature impacts the frequency measurement and can create false mass readings. Thin film deposition controllers currently on the market have no good way of distinguishing frequency shifts related to mass from frequency shifts related to temperature, resulting in thickness errors and poor PID control. This can be detrimental to complex coating processes due to the low deposition rates and incredibly thin layers required. Thermal shocks can occur at any point in a deposition process and can cause unnecessary PID-loop corrections, triggering non-uniform deposition in respect to time. This means that the quality throughout the bulk of the material is inadequate. For very thin films, the thickness termination may not be at the real intended thickness because the process time window is small compared to the time allowed for a QCM to recover from a thermal shock event.

INFICON has patented a new temperature compensation technique for SC-cut crystals to remove the effects of temperature variation on the QCM without the need for additional hardware or custom and expensive sensors.

Please join us for the ‘Temperature Compensation for QCMs’ webinar, hosted by Sheldon Wayman, Product Engineer for INFICON Inc.

20 minutes
English
Más información
Webinar
SMART-Spray, I·BOOST, SPRAY-Check

Smart essentials for intelligent leak detection

33 minutes
English
Más información
Webinar
Introducing Trigon™

A new future proof Hot Ion Gauge generation from INFICON

Más información
Webinar
FabTime®: Improve Fab Cycle Time by Tracking the Right Equipment Reliability Metrics

Most people, when asked, cite equipment downtime as a top contributor to cycle time in their wafer fabs. Downtime impacts cycle time by taking away buffer capacity (driving tools to a steeper part of the operating curve), increasing process time variability (because lots must wait during downtime events), and reducing the available number of qualified tools during a given day or shift. Understanding these effects suggests specific metrics that are helpful for driving cycle time improvement and other metrics that are less useful. In this webinar, Dr. Jennifer Robinson, Cycle Time Evangelist for INFICON, will teach participants to select the best downtime metrics and operating practices for cycle time improvement. The session will include chart examples from the FabTime® reporting module.

06 nov 2024 | 5:00 PM (UTC +2)
60 minutes
English
Más información
Webinar
CrystalSix and Crystal 12 Troubleshooting and Maintenance

CrystalSix and Crystal 12 are rotary Quartz Crystal Monitors utilized in OLED, Solar and Semiconductor applications, to name a few.  QCMs like these also sometimes require user troubleshooting and maintenance to ensure good connectivity as well as crystal positioning within the aperture. During this webinar you will learn about the CrystalSix and Crystal12 and best practices to troubleshoot and maintain them.

60 minutes
English
Más información
Necesitamos su consentimiento para el contenido de video
Más información